Recent

Check Out Our Forum Tab!

Click On The "Forum" Tab Under The Logo For More Content!
If you are using your phone, click on the menu, then select forum. Make sure you refresh the page!

The views of the poster, may not be the views of the website of "Minnesota Outdoorsman" therefore we are not liable for what our members post, they are solely responsible for what they post. They agreed to a user agreement when signing up to MNO.

Author Topic: Auger engine brands?  (Read 2921 times)

0 Members and 1 Guest are viewing this topic.

Offline Go Big Red!

  • Master Outdoorsman
  • Posts: 1761
  • Karma: +0/-0
Since Tecumseh went out of business 2 years ago, what brand of engine has Jiffy switched to?  My Jiffy still has a Tecumseh motor and replacements parts are increasing hard to find.  What does Strikemaster use?
Take a kid hunting and fishing... It'll be the best thing for generations to come.

Offline Randy Kaar

  • Master Outdoorsman
  • Posts: 3112
  • Karma: +1/-0
  • Randy aka bh
I have read that they went with the Solo engine, Dont know anything about how
good the new engines are.

randy
Voted #1 Outdoors Website in MN ( www.mnoutdoorsman.com )!
bonehead149@yahoo.com
bonehead@mnoutdoorsman.com

Offline Go Big Red!

  • Master Outdoorsman
  • Posts: 1761
  • Karma: +0/-0
I have read that they went with the Solo engine, Dont know anything about how
good the new engines are.

randy

I have been told it's a Chinese made motor.   :scratch:
Take a kid hunting and fishing... It'll be the best thing for generations to come.

Offline FireRanger

  • Master Outdoorsman
  • Posts: 573
  • Karma: +0/-0
The Solo brand of motor is of German descent sir.
Going South......in a manner of speaking!

Offline Go Big Red!

  • Master Outdoorsman
  • Posts: 1761
  • Karma: +0/-0
What does Strikemaster have? I thought they went German?
Take a kid hunting and fishing... It'll be the best thing for generations to come.

Offline eyeguy

  • Posts: 4
  • Karma: +0/-0
Solo is German engineered but built in and with parts from china

Offline DDSBYDAY

  • Master Outdoorsman
  • Posts: 5564
  • Karma: +1/-1
  • 2012 MNO Fishing Challenge Champion
    • Advanced Tackle Innovations
    Just in case you guys are still on here.  My strikemaster Lazer mag throttle froze up last weekend.  I had sharp blades so I was able to get two holes drilled.  I am going to fish tomorrow and I tested it.  The throttle is unfroze but I am afraid I may have stretched something.  I does not seem to get to max rpms at full throttle. Is there an adjustment screw for the throttle cable?   There is a screw right where the cable enters the engine.  I can't really see any other areas for adjustment.  :scratch:
Pai Mei tells the Godfather when it's time to tell Wayne  to pimp slap Eastwood.

Offline Go Big Red!

  • Master Outdoorsman
  • Posts: 1761
  • Karma: +0/-0
Usually the throttle cables are stranded metal so it's unlikely you stretched it out.  There is, not sure if yours has this, a black plastic covering that the cable can slide through.  Some lawnmowers have this a a throttle cable for high and low speed.  If this casing/covering gets wrecked, the throttle won't work properly.
Take a kid hunting and fishing... It'll be the best thing for generations to come.

Offline AJDodgerf

  • Outdoorsman
  • Posts: 40
  • Karma: +0/-0
Usually where teh throttle cable attachews to the side of the engine there is a bolt that tightens down on the end of the cable.  If yours i slike mine when the cable freezes and you squeeze the handle, the cable gets pulled out a little.  All you should have to do is loosen this bolt slide the cable back in a small amount and then tighten the bolt again.  This happens about once a year to mine if it gets laid down in the snow.
In God we trust
2012 Deer Hunting Team Champion

Offline DDSBYDAY

  • Master Outdoorsman
  • Posts: 5564
  • Karma: +1/-1
  • 2012 MNO Fishing Challenge Champion
    • Advanced Tackle Innovations
     Used it this morning.  Something is definitely wrong.  It's better than last weekend but still not reaching max rpms.  Runs fine.  I am going to bring it in and warm it up.  It sounds like what you mentioned.  Thanks guys.
Pai Mei tells the Godfather when it's time to tell Wayne  to pimp slap Eastwood.